Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
Every person seems to have their private idea involving Installing A Bathtub.
Setting up a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult job. If the old tub is easily available, the task can move rapidly; if you have to open a wall to eliminate the old bathtub and also place the new tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have certified yourself for the task as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to think about employing one before you start. Chances are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a new tub as well as don't need to change the setup of your previous water pipes.
Your devices and also material list need to make up the following:
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, put the bath tub in the called for setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the level reads degree.
To mount taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the bath tub must wait until the tub has actually been utilized at the very least once as this will settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind needs to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to problems with moisture and feasible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to allow for the motion experienced when the bathtub is in use. The sealant can break rather early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that portion was really helpful. Sharing is nice. Who knows, you may be helping someone out. Thank you for your time. Visit us again soon.
Get Started Report this page